服務熱線: 0531-68828688
新聞資訊
您當前位置: 首頁 - 新聞資訊 - 行業快訊
企業新聞行業快訊政府關懷黨政活動
立式玻璃鉆銑機是如何進工作流程的?

2021.08.13威力智能

立式玻璃鉆銑機為PLC自動控制,操作時只需將玻璃放在傳送帶上,輸入鉆孔位置數據,啟動按鈕,自動定位后鉆削所有孔位,完成工作后自動停機,鉆孔效率高,孔位準確,適用于建筑玻璃與家具玻璃的加工;彩色人機觸摸屏操作自動化控制,介面清晰、操作簡便參數設定后一次加工完成;PLC程序控制,具有自動檢測、診斷功能,電路穩定性高、對作業環境適用性大,并可進行遠程維護、升級。

The vertical glass drilling and milling machine is automatically controlled by PLC. During operation, just put the glass on the conveyor belt, input the drilling position data, start the button, drill all hole positions after automatic positioning, and stop automatically after completing the work. The drilling efficiency is high and the hole position is accurate. It is suitable for the processing of architectural glass and household glass; Color man-machine touch screen operation automation control, clear interface and simple operation, and one-time processing is completed after parameter setting; PLC program control, with automatic detection and diagnosis functions, high circuit stability, great applicability to the working environment, and remote maintenance and upgrading.

使用方法:
usage method:
1.鉆玻璃時,立式玻璃鉆孔機下鉆頭易擠碎玻璃,所以鉆薄玻璃時,壓力時,壓力必須調得很低,可在0.18~03MPa范圍內變化,鉆厚玻璃時,壓力可以上升到0.46MPa左右。
1. When drilling glass, the drill bit under the vertical glass drilling machine is easy to crush glass. Therefore, when drilling thin glass, the pressure must be adjusted very low and can vary within the range of 0.18 ~ 03mpa. When drilling thick glass, the pressure can rise to about 0.46mpa.
2.每班工作開始前,應先給立式玻璃鉆孔機各注油部位注入潤滑油,并檢查皮帶松緊程度,上、下鉆軸運轉有無異常,鉆頭是否磨損,待一切正常后方可開始工作。
2. Before the start of each shift, inject lubricating oil into each oil filling part of the vertical glass drilling machine, check the tightness of the belt, whether the operation of the upper and lower drilling shafts is abnormal, and whether the drill bit is worn. The work can be started only after everything is normal.
3.接料抽屜中的芯料應及時進行清理,否則料芯堆積太多會卡死接料器。特別是鉆削直徑大于100mmj的大孔時,每鉆幾個孔就應清理一次。
3. The core material in the receiving drawer shall be cleaned in time, otherwise too many cores will jam the receiver. In particular, when drilling large holes with a diameter greater than 100mmj, clean them every few holes.
4.清理立式玻璃鉆孔機芯料時應使接料器處于接料位置,以便接料抽屜能順利抽出,所以清理玻璃鉆孔機芯料時要上鉆頭啟動旋轉,此時接料器便處于接料位置,可以方便地清理料芯。
4. When cleaning the core material of the vertical glass drilling machine, the feeder should be in the receiving position so that the receiving drawer can be pulled out smoothly. Therefore, when cleaning the core material of the glass drilling machine, the drill bit should be started to rotate. At this time, the feeder will be in the receiving position, which can easily clean the core.
聯系我們

全國銷售熱線:

0531-68828688 87987918

郵箱:jnweljq@weiliglass.com

地址:

山東省德州市齊河縣劉橋鎮齊劉路002號

立即訂購

山東省德州市齊河縣劉橋鎮齊劉路002號
0531-68828688 87987918
www.weiliglass.com
欧美裸体柔术牲交视频,欧美性色欧美a在线播放,欧美xxxx狂喷水,偷窥中国隐私xxxx <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>