服務熱線: 0531-68828688
新聞資訊
您當前位置: 首頁 - 新聞資訊 - 行業快訊
企業新聞行業快訊政府關懷黨政活動
中空玻璃打膠機調試步驟

2021.08.16威力智能

中空玻璃打膠機在中空玻璃制作過程中,有一個環節是非常關鍵的,就是用結構膠將兩片玻玻璃密封,由于人工打膠慢,封閉不好,所以大量的生產中空玻璃就需要中空玻璃打膠機,下面就帶大家一起來了解一下中空玻璃打膠機的調試方法
Insulating glass gluing machine in the manufacturing process of insulating glass, one link is very key, that is, the two pieces of glass are sealed with structural glue. Due to the slow manual gluing and poor sealing, a large number of insulating glass production requires insulating glass gluing machine. Let's take you to understand the debugging method of insulating glass gluing machine
1、首先打開中空玻璃打膠機的氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,然后在顯示屏上找到原 點設定,點擊輔助原 點設定,然后點擊頭部原 點設定,注意原 點設定時避免頭部和輔助吸盤碰撞.設定好之后返回設定玻璃厚度,輸入完以后,點擊設置進入.等命令位置和當前位置數值一致即可

1. First, turn on the air pump switch, main power switch and console switch of the insulating glass gluing machine, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, return to the set glass thickness, and after input, Click set to enter. Wait until the command position is consistent with the current position value

2、打開一桶膠按鈕,按工作選擇拍膠啟動,在按伐開.此時膠頭已經出膠,等看不見白膠,以混均勻以后按伐關,在按鏈接生產線,此時可以自動打膠.開始打膠要看每條邊每個角打膠是否均勻
2. Open a bucket of glue button, press the work selection to start shooting glue, and then press cutting open. At this time, the glue head has been out of glue, and white glue can not be seen. After mixing evenly, press cutting off, and then press the link production line. At this time, glue can be applied automatically. To start gluing, it depends on whether glue is applied evenly at each corner of each side
3、如果需要調整打膠機的壓力,可以在屏幕上點擊返回找到密封配方,會顯示當前密封壓力,如果每條邊都缺膠,那么可增加壓力,壓力大膠量大,壓力小膠量就小.如果發現某條邊膠量不夠時,在密封配方中會顯示有向上密封,上部密封,向下密封,和下部密封,開始打膠的那條邊就是向上密封,然后順序從上
3. If you need to adjust the pressure of the glue applicator, you can click back on the screen to find the sealing formula, and the current sealing pressure will be displayed. If there is a lack of glue on each side, you can increase the pressure. If the pressure is large, the glue quantity is large, and the pressure is small, the glue quantity will be small. If you find that the glue quantity on one side is not enough, there will be upward seal, upper seal, downward seal, and lower seal in the sealing formula, The side that starts gluing is sealed upward, and then from top to bottom
4、中空玻璃打膠機如果發下只有某條邊膠少或膠多時,調整掃描膠量細微調整,數值大膠量就大,數值小膠量就小.然后說下到末端伐關的距離,數值大,膠嘴到末端膠量少,數值小膠量大
4. If the insulating glass glue applicator issues only a certain edge with less or more glue, adjust the scanning glue amount by fine adjustment. If the value is large, the glue amount will be large, and if the value is small, the glue amount will be small. Then say the distance from the bottom to the end. If the value is large, the glue amount from the glue nozzle to the end will be small, and the value is small, and the glue amount will be large
聯系我們

全國銷售熱線:

0531-68828688 87987918

郵箱:jnweljq@weiliglass.com

地址:

山東省德州市齊河縣劉橋鎮齊劉路002號

立即訂購

山東省德州市齊河縣劉橋鎮齊劉路002號
0531-68828688 87987918
www.weiliglass.com
欧美裸体柔术牲交视频,欧美性色欧美a在线播放,欧美xxxx狂喷水,偷窥中国隐私xxxx <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>